路由器RIP动态路由配置
1、配置计算机PC1
IP: 192.168.1.2
Submask: 255.255.255.0
Gateway: 192.168.1.1
2、配置计算机PC2
IP: 192.168.2.2
Submask: 255.255.255.0
Gateway: 192.168.2.1
3、配置交换机
Switch>en
Switch#conf t
Switch(config)#hostname S3
S3(config)#vlan 10
S3(config-vlan)#exit
S3(config)#vlan 20
S3(config-vlan)#exit
S3(config)#int fa0/10
S3(config-if)#switchport access vlan 10
S3(config-if)#exit
S3(config)#int fa0/20
S3(config-if)#switchport access vlan 20
S3(config-if)#exit
S3(config)#end
S3#show vlan
4、配置交换机
S3#conf t
S3(config)#int vlan 10
S3(config-if)#
S3(config-if)#ip address 192.168.1.1 255.255.255.0
S3(config-if)#no shutdown
S3(config-if)#exit
S3(config)#int vlan 20
S3(config-if)#
S3(config-if)#ip address 192.168.3.1 255.255.255.0
S3(config-if)#no shutdown
S3(config-if)#end
S3#show ip route
S3#show running
5、配置路由器R1
R1>en
R1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
R1(config)#hostname R1
R1(config)#int fa0/0
R1(config-if)#no shutdown
R1(config-if)#ip address 192.168.3.2 255.255.255.0
R1(config-if)#exit
R1(config)#int s2/0
R1(config-if)#no shutdown
R1(config-if)#ip address 192.168.4.1 255.255.255.0
R1(config-if)#clock rate 64000
R1(config-if)#end
R1#
R1#show ip route
C 192.168.3.0/24 is directly connected, FastEthernet0/0
R1#
R1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
R1(config)#router rip
R1(config-router)#network 192.168.3.0
R1(config-router)#network 192.168.4.0
R1(config-router)#version 2
R1(config-router)#exit
R1(config)#
6、配置路由器R2
Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname R2
R2(config)#int fa0/0
R2(config-if)#no shutdown
R2(config-if)#
R2(config-if)#ip address 192.168.2.1 255.255.255.0
R2(config-if)#exit
R2(config)#int s2/0
R2(config-if)#no shutdown
R2(config-if)#
R2(config-if)#ip address 192.168.4.2 255.255.255.0
R2(config-if)#end
R2#
R2#show ip route
R2#conf t
R2(config)#router rip
R2(config-router)#network 192.168.2.0
R2(config-router)#network 192.168.4.0
R2(config-router)#version 2
R2(config-router)#end
R2#
7、测试连通性：
PC1 Ping PC2
Ping 192.168.2.2
8、配置交换机路由
S3>en
S3#conf t
S3(config)#ip routing
S3(config)#router rip
S3(config-router)#network 192.168.1.0
S3(config-router)#network 192.168.3.0
S3(config-router)#version 2
S3(config-router)#end
S3#
S3#show ip route
