思科交换机常用命令及配置

2025-09-30 03:45:43

1、打开思科交换CLI,首先进入的是用户模式,如果要进行配置操作需要进入特权模式。

Switch>enable

Switch#

思科交换机常用命令及配置

2、从特权模式进入全局配置模式

Switch#configure terminal

Switch(config)#

思科交换机常用命令及配置

3、在特权模式下可以对交换机进行命名,这样在配置多台交换机时,避免将配置写错交换机。

Switch(config)#hostname cisco-sw1

思科交换机常用命令及配置

4、配置交换端口密码,登录特权模式时需要输入该密码,避免设备被其他人使用。

cisco-sw1(config)#enable password cisco

ps:password表示密码为明文

思科交换机常用命令及配置

5、给交换机配置使能密码,进入特权模式时需要输入密码才能进入腊脾,避免设备可以被其他人员使用。

cisco-sw1(config)#enable secret ciscoswitch

ps:secret表示密码用的密文

思科交换机常用命令及配置

思科交换机常用命令及配置

6、交换机配置VLAN,并给将端口加入到该VLAN:

cisco-sw1(config)#vlan 2

cisco-sw1(config-vlan)#name test

cisco-sw1(config-vlan)#exit

cisco-sw1(config)#interface  fastEthernet 0/1

cisco-sw1(config-if)#switchport mode access

cisco-sw1(config-if)#switchport access vlan 2

思科交换机常用命令及配置

思科交换机常用命令及配置

7、进入交换机某一端口

switch> enable

switch#configure terminal

switch(conf)# interface fastehernet 0/1

switch(conf-if)#

思科交换机常用命令及配置

8、show:查看命令,交换机的所有配置和其它相关信息都需要通过show命令查看。

switch> enable

switch# show version 察看系统中的所有版本信息

switch#show  vlan id 1 查看交换机有关vlan配置信息

switch#show running-configure 查看交换机当前起作用的配置信息

switch#show interface fastethernet 0/1 察看交换机1 接口具体配置和统计信息

switch#show mac-address-table 查看mac地址转发表

思科交换机常用命令及配置

思科交换机常用命令及配置

思科交换机常用命令及配置

思科交换机常用命令及配置

思科交换机常用命令及配置

9、交换机恢复出厂

switch> enable

switch# erase startup-configure

switch# reload

思科交换机常用命令及配置

10、telnet 远程登录设置:帮蹲

switch>en

switch#configure terminal

swich(conf)#enable password cisco 以cisco 为特权模式密码

swich(conf)#interface vlan 1 以vlan 1端口作为远程登录的接口,其他端口亦可

swich(conf-if)#ip address 192.168.1.1 255.255.255.0

swich(conf-if)#no shut

swich(conf-if)#exit

swich(conf)line vty 0 4 设置0-4 个用户可以telnet 远程登陆

swich(conf-line)#password 123456

swich(conf-line)#login

思科交换机常用命令及配置

11、SSH远程登录设置:

Switch#conf t

Enter configuration commands, one per line.  End with CNTL/Z.

Switch(config)#hostname cisco-sw1   交菌缝泪换机重新命名

cisco-sw1(config)#ip domain-name cisco.com 配置域名

cisco-sw1(config)#line vty 0 4

cisco-sw1(config-line)#transport input ssh 登录方式为SSH

cisco-sw1(config-line)#exit

cisco-sw1(config)#crypto key generate rsa 配置秘钥

The name for the keys will be: cisco-sw1.cisco.com

Choose the size of the key modulus in the range of 360 to 2048 for your

General Purpose Keys. Choosing a key modulus greater than 512 may take

a few minutes.

How many bits in the modulus [512]: 1024 思科推荐使用1024

% Generating 1024 bit RSA keys, keys will be non-exportable...[OK]

思科交换机常用命令及配置

思科交换机常用命令及配置

声明:本网站引用、摘录或转载内容仅供网站访问者交流或参考,不代表本站立场,如存在版权或非法内容,请联系站长删除,联系邮箱:site.kefu@qq.com。
猜你喜欢